(Your shopping cart is empty)

  Home > Syclone/Typhoon Products >

Velosyty SyTy 60lb Injector/Chip Combo - Flow Matched
Velosyty SyTy 60lb Injector/Chip Combo - Flow Matched
 
Velosyty Chip
Typically takes 7-10 days to make the chip, so plan ahead!
Please read the features of the chip below, and make sure you have a scantool!
Normal Price: $434.99


Stock Status:(Out of Stock)
Availability when in stock:: Usually Ships in 1 to 2 Weeks
Product Code: 1040-FM


Car Type*:


Chip Type*:
Street (intended for pump gas, no alcohol injection)- Read below about difference between Street and Alcohol
Alcohol (must use alcohol injection)
Race (race fuel)
Chip for E85 Fuel (minimum 50lb injectors required)

MAP Sensor using with this chip*:
3-BAR MAP

Fuel Octane*:

Your Setup

Turbo:


Intercooler:


Cylinder Heads:


Camshaft:


What wideband system do you have?*:


Optional Secondary Chip Program:
No, just leave the standard single chip program on there
Yes, I want a secondary chip program [Add $59.99]- Describe the secondary program you would like in the notes (race, alky, etc).

Other Info:
Keep this short, enter extra info during checkout.

 
Description
 
New Version 2 !!!
60lb/hr injector and Velosyty chip combo deal (these injectors are flow matched to +/-2% of each other)
Typically takes 7-10 days to make the chip, so plan ahead!
If you don't own a scantool, then this chip is not for you. If you are expecting to improve and refine the performance of your car, you need a way to confirm sensor readings and troubleshoot. I cannot help you with troubleshooting without any data. A good portable scantool is the Scanmaster 3, sold in this webstore, but something like Tunerpro or Datamaster work well too. Requires a 3-bar MAP sensor.
A completely new program for the Syclone/Typhoon! Many improvements to the chip programming to improve cold starts, idle, response, and general driveability. Also includes the ability to read a wideband O2 system (connected to the ECM), and makes corrections at full throttle (above 10psi boost).
The chip is mounted on a memcal adapter. You remove your old memcal and plug it into the new adapter, then plug the adapter back into your ECM. (You need an old stock-type memcal for it to work. The programming on the old memcal doesn't matter, as long as it was originally made for a Syclone/Typhoon.)
Optional secondary program can be put on the same chip ($55). It is selected by a small switch on the memcal adapter.
Knock Alert, flashes the check engine light if knock retard exceeds 5 degrees
Compatible with "EGR delete"
Also includes user adjustable features.
There are 2 rotary dials for basic idle and WOT fuel control, and 3 on/off switches for some other optional features, like open loop mode, open loop idle, and wideband/narrowband simulation mode.
There are other internal user features, these are adjusted using a procedure with the throttle and watching some numbers on a scantool.

User adjustable features are:
1. High boost fuel
2. Mid boost fuel
3. Low gear timing
4. High gear timing
5. Initial wastegate duty cycle
6. Target boost
7. Closed loop WOT A/F target (requires a wideband system connected to the ECM)

Download chip instructions here: http://www.turbotweak.com/velosytydoc2.pdf



Note: This part is intended for off-road use only, as it may not meet emissions standards. It is up to the purchaser to determine how it will be used.


Browse for more products in the same category as this item:

Syclone/Typhoon Products
TurboTweak
3567 Purcell Dr.
Salem, IL 62881
eric@turbotweak.com
 About Us
 Privacy Policy
 Send Us Feedback
 
Company Info | Advertising | Product Index | Category Index | Help | Terms of Use
Copyright © 2004 TurboTweak. All Rights Reserved.
Built with Volusion